
Licensed, insured crews for black mold and stachybotrys cleanup
Toxic Mold Removal in PACOIMA, California
Toxic Mold Removal in PACOIMA, California is what we do when mold has moved past a surface stain and into your air, drywall, or crawl space. We handle toxic black mold removal PACOIMA California homeowners call about after a roof leak, a slow supply line, or a flooded garage. Our crews test, contain, and remove the growth, then verify the air is clean before we pack up.
What's included
What Our Toxic Mold Removal Includes
Every toxic mold removal job includes inspection, containment, removal, cleaning, and clearance testing. Here is what is covered in a standard scope. Add-ons like reconstruction, HVAC cleaning, or crawl space encapsulation are quoted separately if needed.
Full Mold Inspection
A certified inspector checks all accessible areas with a moisture meter, thermal imaging camera, and boroscope. We identify the mold species, locate the moisture source, and document everything with photos. You get a written report and scope of work.
Containment and Air Scrubbing
We seal the work area with 6-mil containment plastic sheeting and duct tape. Negative air machines with HEPA filters and air scrubbers run continuously to prevent spores from spreading. This protects the rest of your home during removal.
Physical Mold Removal
Contaminated drywall, insulation, and debris are removed, bagged, and disposed of per Cal/OSHA rules. We HEPA vacuum all surfaces and treat framing with an antimicrobial spray. For heavy growth, we use dry ice blasting mold removal to avoid adding moisture.
Moisture Source Correction
Mold returns if the water source is not fixed. We identify and repair the cause, whether it is a roof leak, plumbing failure, poor drainage, or high humidity. We also install dehumidifiers or ventilation where needed to keep the space dry.
Post-Remediation Clearance Testing
After cleaning, we collect spore trap samples inside the containment and outside as a control. An accredited lab analyzes the samples. You receive the report showing indoor spore counts at or below outdoor levels. If it does not pass, we re-clean at no charge.
Service overview
Toxic Mold Removal in PACOIMA, California
Toxic Mold Removal in PACOIMA, California is a containment-and-removal process that targets mold species producing mycotoxins, most often Stachybotrys chartarum, the black mold that grows on wet drywall, ceiling tile, and wood framing. We do not just spray bleach and paint over it. We find the moisture source with a moisture meter and thermal imaging camera, seal the work area with containment plastic sheeting, run a negative air machine with HEPA filters, and physically remove contaminated materials. Everything gets HEPA vacuumed, wiped with an antimicrobial spray, and where code allows, sealed with an encapsulation coating.
PACOIMA sits in the northeast San Fernando Valley, where summer heat pushes attic temperatures past 140 degrees and winter rain finds every failed roof flashing. That swing feeds black mold growth in attics, crawl space mold under older homes, and bathroom mold behind tile. If you have been searching for toxic mold removal in PACOIMA California near me, the first step is a proper inspection, not a guess. We test with spore traps, document what we find, and give you a written scope before any demolition starts.
The service timeline
How Our Toxic Mold Removal Process Works
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection and Testing
A certified mold inspector walks the property with a moisture meter, thermal imaging camera, and boroscope to find hidden growth behind walls and under floors. We set spore traps to identify the species and airborne count. This stage takes 60 to 90 minutes for a typical Pacoima home, and you get the findings in writing.
Containment and Air Control
We seal the work zone with containment plastic sheeting and duct tape, then install a negative air machine with HEPA filters to pull air out and keep spores from migrating. Air scrubbers run continuously. Setup usually takes one to two hours depending on how many rooms are affected.
Removal and Cleaning
Contaminated drywall, insulation, and framing are removed, bagged, and hauled out. We HEPA vacuum all surfaces, then apply an antimicrobial spray. For heavy growth on structural wood, we use dry ice blasting mold removal, which lifts spores without soaking the wood. A fogger treats hard-to-reach cavities.
Repairs and Sealing
Where framing is salvageable, we treat it with a mold remediation chemical and apply an encapsulation coating. New drywall and insulation go back in. We also address the moisture source, whether that is a roof repair, a plumbing fix, or a dehumidifier in a crawl space.
Clearance Testing
After work is complete, we run post remediation mold testing with spore traps and compare indoor counts to an outdoor control sample. If the numbers are not where they need to be, we re-clean at no extra charge. You get the lab report and a written clearance before we close the job.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Moisture Meter
Pin-type and pinless meters measure moisture content in drywall, wood, and concrete. They help us find hidden water sources and map the extent of contamination before we open a wall.
Thermal Imaging Camera
Infrared cameras detect temperature differences caused by moisture. We use them to scan walls, ceilings, and floors for hidden leaks and wet spots that are not visible to the eye.
Boroscope
A boroscope is a flexible camera we insert into small holes to inspect inside wall cavities, behind baseboards, and under floors. It lets us see mold growth without major demolition.
Negative Air Machine
We use negative air machines with HEPA filters to create negative pressure inside containment. This keeps spores from escaping into the rest of your home while we work.
Air Scrubber
Air scrubbers run continuously during remediation to filter airborne spores and particles. They work with the negative air machine to maintain clean air in the containment.
Dry Ice Blasting Machine
For heavy mold on wood framing, we use dry ice blasting. It lifts mold and spores without water or chemicals, leaving a clean surface that is ready for encapsulation.
Spore Trap
Spore traps collect airborne mold spores for lab analysis. We use them before remediation to establish a baseline and after to confirm clearance.
Use cases
When to Call for Toxic Mold Removal
These examples show how the service framework adapts rather than forcing every call through one repair.

Crawl Space Mold Remediation in Arleta
A fourplex in Arleta had standing water in the crawl space after winter storms. Mold grew on the floor joists and subfloor, and tenants complained of musty odors. Moisture readings were above 30 percent in the wood. → We removed contaminated debris, treated the joists with a mold remediation chemical, and installed a vapor barrier. A dehumidifier was added to keep humidity below 50 percent. Clearance testing confirmed the air was clean. The job took four days.
Attic Mold Removal in Lake View Terrace
A roof leak during winter rains soaked the attic sheathing and insulation. Black mold spread across the underside of the roof. The homeowner smelled a musty odor in the hallway and saw dark staining on the ceiling. → We contained the attic, removed contaminated insulation, and treated the sheathing with dry ice blasting. New insulation was installed, and the roof leak was repaired. Post-remediation testing showed clean air. The job took three days.
Problems we solve
Toxic Mold Problems We Solve in Pacoima
These are the most common mold issues we see in Pacoima homes and businesses. If any of these sound familiar, call us for an inspection before the damage spreads.
Black mold growth behind walls after a hidden leak
We use thermal imaging and boroscopes to find hidden growth, then contain and remove contaminated materials. We treat framing with antimicrobial spray and verify with spore trap testing. Most jobs are completed in two to four days.
Musty odors that keep coming back after cleaning
We locate the moisture source, remove the mold colony, and treat the area with a fogger and HEPA filtration. For HVAC mold contamination, we clean the system and replace filters. The odor is gone when the mold is gone.
Crawl space mold from poor drainage and humidity
We remove contaminated debris, treat joists with a mold remediation chemical, install a vapor barrier, and add ventilation or a dehumidifier. This stops the mold and prevents it from returning.
Post-flood mold after a storm or plumbing failure
We extract water, dry the structure with Dri-Eaz and Phoenix Restoration equipment, then remediate any mold growth. We document everything for insurance and provide clearance testing before we finish.
Pricing process
Toxic Mold Removal Pricing in Pacoima
$1,200 - $9,000 depending on scope
Square footage affected
The larger the contaminated area, the more materials need removal and disposal. A 10-square-foot patch is a different job than a 200-square-foot crawl space. We measure and price by the actual scope.
Mold species and severity
Toxic black mold removal PACOIMA California jobs involving Stachybotrys require more containment and cleaning than common surface molds. Severity also matters: surface growth on drywall is easier to remove than mold that has penetrated framing.
Access and containment difficulty
Crawl spaces, attics, and wall cavities are harder to access than open rooms. We may need to build special containment or use ladders and scaffolding. This adds labor time and cost.
How much does toxic mold removal cost in PACOIMA California?
Most residential toxic mold removal jobs in Pacoima run $1,500 to $6,500 in 2026, depending on square footage and how deep the growth goes. A single bathroom with surface mold might be $1,200 to $2,000. Crawl space or attic jobs with structural contamination often land between $4,000 and $9,000. Emergency calls and hazardous mold cleanup PACOIMA jobs with extensive containment cost more. We give you a flat price after inspection.
How do I know if I have toxic black mold in PACOIMA?
You cannot confirm toxic black mold by color alone. Stachybotrys is dark green-black and usually slimy, but several less harmful molds look similar. The reliable signs are a musty odor, water stains that keep coming back, and allergy-like symptoms that ease when you leave the house. The only way to know for sure is spore trap testing. We inspect, sample, and send to a lab for species identification.
Who does black mold remediation near me in PACOIMA?
Our crews are based in the Pacoima area and cover Hansen Hills, Arleta, Lake View Terrace, Sun Valley, Shadow Hills, and La Tuna Canyon. We handle both residential and commercial jobs, from single-family homes to apartment buildings and retail spaces. Call (833) 929-5837 and we will schedule an inspection, often the same day. For emergencies, we run 24/7.
Is toxic mold removal covered by insurance in PACOIMA California?
It depends on the cause. Most homeowners policies cover mold remediation when it results from a covered water loss, like a burst pipe or appliance failure. They typically do not cover mold from long-term neglect or flooding. We document the moisture source, photograph affected materials, and provide lab results so your adjuster can process the claim. We work directly with most major carriers.
Ready when you are
Get Toxic Mold Removal in PACOIMA, California Today
If you see dark staining, smell a musty odor, or have had recent water damage, do not wait. Mold spreads fast in Pacoima heat. Call (833) 929-5837 for a same-day inspection and a flat-price quote. Licensed, insured, and IICRC-certified. We answer 24/7.

Talk with the local team
Request Toxic Mold Removal
Call us at (833) 929-5837 or email info@moldremediationservicepacoima.com. We answer the phone 24/7 for emergencies and we schedule same-day estimates for non-emergency work. If you are not sure whether you need testing or full remediation, call us and we will walk you through it. No pressure, no sales pitch.



