Dry Ice Blasting Mold

CO2 blasting kills mold on contact and leaves zero residue

Dry Ice Blasting Mold in PACOIMA, California Without the Mess

Dry Ice Blasting Mold in PACOIMA, California is the fastest way to strip black mold off framing, brick, and crawl space joists without soaking your home. We blast with -109°F dry ice pellets that lift spores and leave nothing behind but a shop-vac pass. If you have musty odors, attic mold, or water damage mold, call (833) 929-5837.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What Dry Ice Blasting Mold Includes

Every dry ice blasting mold job we quote includes containment, blasting, antimicrobial treatment, and post-blast testing. We do not nickel-and-dime you on plastic sheeting or lab fees. If the scope changes because we find hidden mold behind a wall, we stop and get your approval before continuing.

01

Containment and Negative Air

We seal the work zone with 6-mil containment plastic sheeting and run a negative air machine with HEPA filters. This keeps spores from spreading to the rest of your home during blasting. Setup takes 45 to 90 minutes.

02

Dry Ice Blasting and HEPA Vacuuming

Our techs blast the mold off framing, brick, concrete, and tile at 150 to 300 PSI, then HEPA vacuum the debris. We keep the vacuum running during blasting to capture spores at the source.

03

Antimicrobial Fogging

After blasting, we fog the cavity with a mold remediation chemical like Concrobium or Benefect. This reaches the crevices and pores the blasting wand cannot touch. Cure time is 4 to 6 hours.

04

Encapsulation Coating

On raw wood framing, we roll on an encapsulation coating to seal remaining hyphae and prevent regrowth. This is required on many jobs to pass post-remediation clearance.

05

Post-Remediation Spore Testing

We pull spore trap samples after the job and compare them to the baseline. You get the lab report in 24 to 48 hours. If counts are still elevated, we re-blast at no charge.

Service overview

What Dry Ice Blasting Mold in PACOIMA, California Does

Dry Ice Blasting Mold in PACOIMA, California is a media-blasting method that fires rice-sized dry ice pellets at 150 to 300 PSI to freeze and lift mold off hard surfaces. The pellets hit at -109°F, flash-freeze the mold, and sublimate straight to gas on impact. No water, no sand, no chemical slurry. That means no secondary moisture problem in a house that already has one. We use it on wood framing, brick, concrete, tile, and metal ductwork where wet blasting would ruin the substrate or push spores deeper.

PACOIMA homes deal with mold differently than coastal cities. Summer heat bakes attics to 140°F, then winter rain finds every failed roof flashing. Older 1950s ranch houses off Van Nuys Boulevard have original cast-iron drains and unvented crawl spaces that stay damp year-round. If you have been searching for dry ice blasting mold in PACOIMA California near me, we run spore trap samples before and after so you can see the drop in airborne counts, not just take our word for it.

No Water, No Secondary DamageTraditional pressure washing and chemical washing push mold spores into drywall paper and subfloor seams. Dry ice blasting mold PACOIMA jobs leave wood at its original moisture reading. We verify with a moisture meter before and after so you know the framing is ready for drywall the same afternoon.
Kills Spores on ContactThe -109°F pellet temperature thermal-shocks mold spores and fractures the cell wall on impact. Lab testing on hard surfaces shows 99%+ spore removal in a single pass. That matters when you are dealing with black mold growth on attic sheathing or crawl space joists where a HEPA vacuum alone leaves roots behind.
Reaches What Scrubbing MissesWe fit a boroscope and angled blasting wand into 2-inch gaps behind baseboards, inside wall cavities, and around HVAC plenums. CO2 blasting mold removal PACOIMA California jobs handle the hidden mold that hand-scrubbing never touches, which is where musty odors keep coming back from.
Dry Ice Blasting Mold by Mold Remediation Service Pacoima
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

How Our Dry Ice Blasting Process Works

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Inspection and Testing

We start with a moisture meter and thermal imaging camera to map the wet zones, then pull spore trap samples from inside and outside the home. You get lab results in 24 to 48 hours. If the mold is contained to one wall, we tell you that instead of quoting the whole house.

Stage 1
02

Containment Setup

We hang 6-mil containment plastic sheeting and run a negative air machine with HEPA filters so spores cannot drift into living space. Every tech suits up in disposable coveralls and respirator cartridges. Setup takes 45 to 90 minutes depending on how many rooms we are sealing off.

Stage 2
03

Dry Ice Blasting

Our techs run the dry ice blasting machine at 150 to 300 PSI, adjusting pressure by substrate. Brick and concrete take higher pressure; old-growth framing takes a lighter pass. A typical attic takes two to four hours. We keep a HEPA vacuum running the whole time to capture what the pellets knock loose.

Stage 3
04

Antimicrobial and Encapsulation

After blasting, we fog the cavity with a mold remediation chemical like Concrobium or Benefect, then roll on an encapsulation coating on raw wood. This seals any remaining hyphae and gives you a clean surface for insulation and drywall. Cure time is 4 to 6 hours.

Stage 4
05

Post-Blast Verification

We pull a second set of spore trap samples and compare them to the baseline. If counts are not where they need to be, we re-blast at no extra charge. You get the lab report, moisture readings, and photos in a single PDF the same week.

Stage 5

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Dry Ice Blasting Machine

Fires rice-sized dry ice pellets at 150 to 300 PSI to freeze and lift mold off hard surfaces. Pressure is adjusted by substrate to avoid pitting wood.

02

Thermal Imaging Camera

Finds hidden moisture behind walls and ceilings before we blast. Mold needs water, so finding the source is step one.

03

Moisture Meter

Reads moisture content in wood and drywall. We use it to confirm the structure is dry before and after dry ice blasting mold.

04

HEPA Vacuum

Captures spores and debris during and after blasting. HEPA filters trap particles down to 0.3 microns.

05

Negative Air Machine

Maintains negative pressure inside containment so spores cannot escape into living space.

06

Boroscope

Inspects inside wall cavities and ductwork where mold hides. Lets us confirm growth before cutting drywall.

07

Fogger

Applies antimicrobial mist after blasting to reach crevices the wand cannot touch. We use Concrobium or Benefect.

Use cases

When to Call for Dry Ice Blasting Mold

These examples show how the service framework adapts rather than forcing every call through one repair.

Dry Ice Blasting Mold
Attic Sheathing After Roof LeakA 900-square-foot attic in Pacoima had black mold across 60% of the roof sheathing after a slow roof leak went unnoticed for two months. Moisture meter readings were 28% in the affected area, and spore trap counts indoors were four times the outdoor baseline. → We contained the attic, blasted the sheathing at 200 PSI for three hours, fogged with Benefect, and applied encapsulation coating. Post-blast moisture readings dropped to 12%, and spore counts came back at outdoor levels.

Crawl Space Joists in Hansen Hills

A Hansen Hills home had crawl space mold on 40 linear feet of floor joists from a slow drain leak. The space had no vapor barrier, and relative humidity was holding at 78%. The homeowner noticed a musty odor in the living room. → We installed a vapor barrier, blasted the joists with dry ice at 250 PSI, and ran a Dri-Eaz dehumidifier for 24 hours. Humidity dropped to 52%, and post-remediation mold testing confirmed clearance.

Bathroom Ceiling in San Fernando Gardens

A San Fernando Gardens apartment had black mold across a 40-square-foot bathroom ceiling from a failed vent fan. The drywall paper was saturated, and the tenant reported allergy symptoms. Spore trap testing confirmed Stachybotrys. → We removed the saturated drywall, blasted the ceiling joists and concrete backer board, fogged with Concrobium, and replaced the drywall. Clearance testing came back clean in five days.

Problems we solve

Mold Problems We Solve With Dry Ice Blasting

Most PACOIMA mold calls come down to one of these four problems. Dry ice blasting mold solves them without the water damage that wet remediation causes.

ISSUE

Black mold growth on attic sheathing after a roof leak

We contain the attic, blast the sheathing at 150 to 250 PSI, fog with antimicrobial, and encapsulate the wood. Post-blast spore testing confirms the air is clear before we pack up.

SYMPTOM

Crawl space mold from unvented foundations and clay soil

Dry ice blasting mold cleans joists and subfloor without adding moisture. We follow with a dehumidifier and encapsulation coating on the wood to stop regrowth.

SIGN

Bathroom mold behind tile and on drywall from steam and leaks

We blast tile and concrete backer board clean, then treat the cavity with antimicrobial fogging. If drywall is saturated, we remove and replace it as part of the scope.

ALERT

HVAC mold contamination spreading spores through the house

We blast the plenum and duct interiors where accessible, HEPA vacuum the system, and apply an antimicrobial spray. Post-remediation mold testing confirms the air handler is clear.

Pricing process

Dry Ice Blasting Mold Pricing in PACOIMA

$900 - $4,500 depending on scope

Phase 01

Square Footage Affected

The more surface area we blast, the longer the job runs. A 200-square-foot attic takes two hours; a 1,200-square-foot crawl space takes six to eight. Square footage is the biggest driver of price.

Phase 02

Access and Containment

Tight crawl spaces and attics with limited entry take longer to set up containment. If we need to cut an access panel or run hose through a second-story window, that adds labor.

Phase 03

Substrate Type

Brick and concrete take higher pressure and more time than wood framing. Tile and grout in bathrooms are slower because we work around fixtures and seams.

Questions before we arrive

Frequently Asked Questions

Dry Ice Blasting Mold
Call (833) 929-5837
How much does dry ice blasting mold cost in PACOIMA California?

Most residential dry ice blasting mold jobs in PACOIMA run $1,200 to $3,800 in 2026, depending on square footage and access. A single bathroom ceiling might be $900 to $1,400. A full attic or crawl space with containment and post-blast testing lands $2,500 to $4,500. Lab fees for spore trap samples run $75 to $150 per sample, and we usually pull two to four.

Is CO2 blasting mold removal safe in PACOIMA?

Yes. Dry ice is food-grade carbon dioxide, and it sublimates to gas on impact, so there is no chemical residue left in your home. The real safety work is containment: we seal the work area with 6-mil plastic and run a negative air machine with HEPA filters so spores do not migrate. Techs wear respirator cartridges and disposable coveralls. You and your family stay out of the containment zone until we clear it.

Who offers dry ice mold remediation near me in PACOIMA?

We do, and we are local. Mold Remediation Service Pacoima runs cryogenic mold removal PACOIMA jobs across the 91331 ZIP code and surrounding areas like Arleta, Sun Valley, and San Fernando Gardens. Call (833) 929-5837 and we can usually schedule an inspection within 24 hours. We carry CSLB licensing and IICRC AMRT certification.

How long does dry ice blasting take in PACOIMA California?

A typical residential job takes four to eight hours of on-site work, split across containment setup, blasting, antimicrobial fogging, and breakdown. The blasting itself runs two to four hours for an average attic or crawl space. Add 24 to 48 hours for lab results on the post-blast spore trap samples. Larger commercial jobs can run two to three days.

Ready when you are

Get Dry Ice Blasting Mold in PACOIMA, California Today

Mold doubles in 24 to 48 hours when moisture is present. Call (833) 929-5837 and we will schedule an inspection, pull spore trap samples, and give you a flat-rate dry ice blasting mold quote. CSLB-licensed, IICRC-certified, and local to PACOIMA.

Dry Ice Blasting Mold

Talk with the local team

Request Dry Ice Blasting Mold

Call us at (833) 929-5837 or email info@moldremediationservicepacoima.com. We answer the phone 24/7 for emergencies and we schedule same-day estimates for non-emergency work. If you are not sure whether you need testing or full remediation, call us and we will walk you through it. No pressure, no sales pitch.

13520 Paxton St, Pacoima, CA 91331, USA, PACOIMA, CaliforniaMain office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now