Attic Mold Testing And Removal

Find hidden attic mold fast. Remove it right the first time.

Attic Mold Testing And Removal in PACOIMA, California

Attic Mold Testing And Removal in PACOIMA, California starts with a certified inspection and ends with a dry, mold-free roof space. If you smell something musty upstairs or spotted dark staining on the roof deck, our team tests the air, finds the moisture source, and removes the growth using IICRC S520 methods. We serve homeowners and property managers across the northeast San Fernando Valley.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What Attic Mold Testing And Removal Includes

Every job is different, but most attic mold testing and removal projects include the same core steps. Here is what is covered in a standard scope. If your attic needs additional work like roof repair or insulation replacement, we tell you upfront and price it separately.

01

Full Attic Inspection

A certified inspector walks the entire attic with a moisture meter and thermal imaging camera. We check the roof deck, rafters, insulation, and every penetration point. A boroscope goes into tight rafter bays. This takes 45 to 90 minutes and gives us a complete picture of what is growing and where.

02

Lab Spore Testing

We set a spore trap in the attic and one outdoors for a baseline comparison. Samples go to an accredited lab and results come back in 24 to 48 hours. The report tells you the mold genus, the spore count, and whether the indoor level is elevated. That report is yours to keep.

03

Containment Setup

We seal the attic access with containment plastic sheeting and set up a negative air machine with HEPA filters. This keeps spores from drifting into your living space during removal. Our technicians wear disposable coveralls and respirator cartridges. Cal/OSHA-compliant protocols on every job.

04

Mold Removal And Treatment

Growth is removed from rafters and sheathing using dry ice blasting or HEPA vacuuming, depending on the surface. We apply an antimicrobial spray from Fiberlock or Concrobium, then an encapsulation coating on bare wood. This is the step that actually gets rid of the mold, not just bleaches it.

05

Clearance Testing

After removal, we run a post remediation spore trap to confirm the attic air is back to normal levels. You get a clearance report showing before-and-after spore counts. If the numbers are not where they should be, we go back in. That is the standard we hold ourselves to.

Service overview

What Attic Mold Testing And Removal in PACOIMA, California Covers

Attic Mold Testing And Removal in PACOIMA, California is a two-part service that identifies mold growth in your roof space and then removes it at the source. We start with a full attic mold inspection PACOIMA California property owners can rely on: a moisture meter and thermal imaging camera map every damp spot, a boroscope checks inside wall cavities and rafter bays, and a spore trap captures air samples for lab analysis. Once we know what is growing and why, we contain the area with plastic sheeting and negative air machines, then remove the growth from rafters, sheathing, and insulation.

Most PACOIMA attics go moldy for the same three reasons: a roof leak that went unnoticed through the dry season, poor ventilation that traps humid air, or a bathroom or HVAC exhaust fan venting straight into the roof space. In a neighborhood like Herrick, where many homes were built in the 1950s and 1960s with minimal soffit venting, one wet winter can be enough to start black mold growth across the entire roof deck. If you need attic mold testing and removal in PACOIMA California near me, we can be on-site the same day.

Same-Day Testing AvailableCall before noon and we can usually have a certified inspector in your attic the same afternoon. We take air samples with a spore trap, run a moisture meter across the roof deck, and give you a straight answer on what is growing and how far it has spread. No waiting a week for a callback.
Source-First RemovalKilling mold without fixing the moisture is a waste of money. We find the roof leak, the blocked soffit vent, or the exhaust fan dumping humid air into the attic, and we correct it. Then we remove the growth. That is why our attic mold remediation PACOIMA jobs do not come back six months later.
HEPA-Contained CleanupWe seal the attic stair or hatch with containment plastic sheeting, run a negative air machine with HEPA filters, and HEPA vacuum every surface before we apply any antimicrobial spray. Spores stay in the attic, not in your living room. Our technicians wear disposable coveralls and respirator cartridges on every job.
Mold Remediation Service Pacoima serving PACOIMA, California
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

Our 5-Step Attic Mold Removal Process

The process flexes to the condition, but these checkpoints keep decisions clear.

01

Phone Assessment

We ask about the smell, any visible staining, recent roof leaks, and how old the home is. That tells us whether you need testing only or a full removal. We schedule a same-day or next-morning visit, and we tell you upfront what the inspection will cost. No dispatch fee.

Stage 1
02

On-Site Inspection

A certified inspector walks the attic with a moisture meter and thermal imaging camera. We check the roof deck, rafters, insulation, and every penetration point. A boroscope goes into tight rafter bays. This takes 45 to 90 minutes depending on attic size and how much stored material is in the way.

Stage 2
03

Lab Testing

We set a spore trap in the attic and one outdoors for a baseline comparison. Samples go to an accredited lab, and results come back in 24 to 48 hours. The report tells you the mold genus, the spore count, and whether the indoor level is elevated. That report is yours to keep.

Stage 3
04

Containment And Removal

If mold is confirmed, we seal the attic access with containment plastic sheeting and set up a negative air machine with HEPA filters. Growth is removed from rafters and sheathing using dry ice blasting or HEPA vacuuming, depending on the surface. We apply an antimicrobial spray, then an encapsulation coating on bare wood.

Stage 4
05

Clearance Testing

After removal, we run a post remediation mold testing spore trap to confirm the attic air is back to normal levels. You get a clearance report showing before-and-after spore counts. If the numbers are not where they should be, we go back in. That is the standard we hold ourselves to.

Stage 5

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Moisture Meter

Measures moisture content in wood and drywall. We use it to find damp spots on the roof deck and rafters that are invisible to the eye. It tells us exactly where the water is coming from.

02

Thermal Imaging Camera

Detects temperature differences that indicate hidden moisture behind surfaces. We scan the entire attic to find wet areas before we start testing. It is fast and non-invasive.

03

Boroscope

A flexible camera that goes into tight rafter bays and wall cavities. We use it to check for mold growth in areas we cannot see directly. It confirms what the moisture meter and thermal camera suggest.

04

Spore Trap

Captures airborne mold spores for lab analysis. We set one in the attic and one outdoors for a baseline comparison. The lab report tells us the mold genus and spore count.

05

Negative Air Machine

Creates negative pressure in the containment zone so spores cannot escape into your living space. We run it with HEPA filters throughout the removal process. This is a critical piece of equipment on every job.

06

HEPA Vacuum

Removes mold spores and debris from surfaces without releasing them back into the air. We vacuum every surface in the containment zone before and after treatment. It is the first step in physical removal.

07

Dry Ice Blasting Machine

Uses compressed dry ice pellets to remove mold from wood without sanding or chemicals. It is fast, clean, and does not damage the surface. We use it on rafters and sheathing where mold has grown into the grain.

Use cases

When to Call for Attic Mold Testing And Removal

These examples show how the service framework adapts rather than forcing every call through one repair.

Attic Mold Testing And Removal
Black Mold on Roof Deck in PacoimaA 1,200-square-foot attic in Pacoima had visible black mold growth across the north-facing roof deck. The bathroom exhaust fan was venting directly into the attic. Moisture readings on the sheathing were above 28 percent. The homeowner had been smelling a musty odor for months. → We contained the attic, ran a negative air machine, and removed the mold with dry ice blasting. The exhaust fan was rerouted to vent outside. After antimicrobial treatment and encapsulation, clearance testing showed spore counts back to normal levels. The musty odor was gone.

Post-Leak Mold in Hansen Hills

A roof leak during winter storms soaked the insulation and roof deck in a Hansen Hills home. The homeowner did not notice until spring when a musty smell appeared in the upstairs bedroom. Testing confirmed elevated spore counts and active mold growth on the rafters. → We removed the moldy insulation, HEPA vacuumed the rafters and sheathing, and treated the wood with antimicrobial spray and encapsulation coating. New insulation was installed. Clearance testing confirmed the attic air was clean. The smell was gone within a week.

Blocked Soffit Vents in Arleta

An Arleta home had blocked soffit vents that trapped humid air against the roof deck. Mold growth covered about 40 percent of the sheathing. The homeowner had allergy symptoms that worsened when the AC ran. Testing confirmed elevated mold spore counts in the living space. → We cleared the blocked soffit vents, added additional venting, and removed the mold with HEPA vacuuming and dry ice blasting. After antimicrobial treatment and encapsulation, clearance testing showed normal spore levels. The homeowner reported fewer allergy symptoms within two weeks.

Problems we solve

Attic Mold Problems We Solve in PACOIMA

Attic mold is a symptom, not the problem. The real issue is always moisture. Here are the most common scenarios we see in PACOIMA homes and how we fix them.

ISSUE

Roof leak that went unnoticed for months

We find the leak entry point with a moisture meter and thermal camera, contain the affected area, remove the mold from rafters and sheathing, and treat the wood with antimicrobial spray and encapsulation coating. We also tell you what roof repair is needed so the leak does not return.

SYMPTOM

Bathroom or kitchen exhaust fan venting into the attic

We confirm the venting problem during inspection, remove the mold, and reroute the exhaust fan to vent outside through the roof or soffit. This is the fix that stops the mold from coming back. Without it, removal is temporary.

SIGN

Blocked or missing soffit vents trapping humid air

We clear blocked soffit vents, add venting if needed, and remove the mold that has already grown. After treatment, we apply an encapsulation coating to the roof deck. Proper ventilation keeps the attic dry year-round.

ALERT

Post-wildfire smoke and ash intrusion

We test the attic air for elevated spore counts, HEPA vacuum all surfaces, and treat with Benefect antimicrobial spray. If mold has already started, we remove it following S520 protocols. We also check the HVAC system for contamination.

Pricing process

Attic Mold Testing And Removal Pricing

$180 - $4,800 depending on scope

Phase 01

Attic Square Footage

A 400-square-foot attic takes less time to contain, treat, and test than a 1,500-square-foot attic. Larger attics need more containment plastic sheeting, more HEPA vacuuming time, and more antimicrobial spray. Square footage is the biggest driver of cost.

Phase 02

Extent of Mold Growth

Surface mold on the rafters is faster to remove than mold that has grown into the sheathing and insulation. If the insulation is contaminated, it has to be removed and replaced. That adds material cost and disposal fees.

Phase 03

Moisture Source Repair

If the moisture source is a bathroom fan venting into the attic, rerouting it is a relatively small additional cost. If the source is a roof leak, the roof repair is a separate scope. We identify the source during inspection and tell you what is needed.

Questions before we arrive

Frequently Asked Questions

Attic Mold Testing And Removal
Call (833) 929-5837
How much does attic mold testing and removal cost in PACOIMA California?

Testing alone runs $180 to $450. Full removal with containment, HEPA vacuuming, and clearance testing typically costs $1,200 to $4,800 depending on attic square footage and how far the growth has spread. A small 400-square-foot attic with surface mold on the rafters is at the low end. A 1,500-square-foot attic with moldy insulation and sheathing is at the high end. We give you a written price before any work begins.

How do I know if my attic has mold in PACOIMA?

The three signs we hear most often: a musty smell that gets stronger on hot days, dark staining on the roof deck or rafters, and allergy symptoms that worsen when the AC runs. If your home was built before 1970 and has never had the roof replaced, check the attic after the first rain of the season. A moisture meter and thermal imaging camera find damp spots that are invisible to the eye. Testing confirms whether it is active mold or old staining.

Who does attic mold remediation near me in PACOIMA?

We do. Mold Remediation Service Pacoima handles attic mold testing and removal across Pacoima, Hansen Hills, Arleta, Lake View Terrace, Sun Valley, Shadow Hills, and the surrounding northeast San Fernando Valley neighborhoods. Our technicians are IICRC AMRT certified and licensed through the California Contractors State License Board. Call (833) 929-5837 and we can usually schedule a same-day inspection.

Can attic mold testing and removal be done same day in PACOIMA California?

Testing can almost always be done same day if you call before noon. Removal depends on scope. A small attic with surface mold on the rafters can be contained and cleaned in four to six hours. Larger jobs with moldy insulation, widespread sheathing growth, or a roof leak that needs repair may take one to two days. We tell you the timeline when we give you the written price.

Ready when you are

Get Attic Mold Testing And Removal in PACOIMA, California Today

Musty smell? Dark staining on the roof deck? Do not wait another season. Call (833) 929-5837 and we can usually schedule a same-day inspection. Testing starts at $180. Written price before any work begins. IICRC AMRT certified technicians.

Attic Mold Testing And Removal

Talk with the local team

Request Attic Mold Testing And Removal

Call us at (833) 929-5837 or email info@moldremediationservicepacoima.com. We answer the phone 24/7 for emergencies and we schedule same-day estimates for non-emergency work. If you are not sure whether you need testing or full remediation, call us and we will walk you through it. No pressure, no sales pitch.

13520 Paxton St, Pacoima, CA 91331, USA, PACOIMA, CaliforniaMain office · technicians serve the full area

Thanks — your request is in. We will contact you shortly.

Call now